Plugin name 'sidebar.BROKEN' is not a valid plugin name, only the characters a-z and 0-9 are allowed. Maybe the plugin has been installed in the wrong directory?

e n g i n k o . s u p p o r t . c e n t e r

Trace:

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
manual_mcf-lw12terwp [2022/01/24 15:26] – [4.2 Other settings] supportadminmanual_mcf-lw12terwp [2025/02/28 12:30] (current) – [10 Declaration of conformity] supportadmin
Line 10: Line 10:
  
   * Do not dismantle or modify in any way.   * Do not dismantle or modify in any way.
-  * The device is not intended to be used as a reference sensor, and enginko Srl will not be held liable for any damage which may result from inaccurate readings.+  * The device is not intended to be used as a reference sensor, and Angel4Future Srl will not be held liable for any damage which may result from inaccurate readings.
   * Avoid mechanical stress   * Avoid mechanical stress
   *  Do not use any detergent or alcohol to clean the device.   *  Do not use any detergent or alcohol to clean the device.
  
 === Disposal information for users === === Disposal information for users ===
-{{:wiki:manual_mcf-LW12TERWP:1200px-weee_symbol_vectors.svg.png?50 |}}**Pursuant to and in accordance with Article 14 of the Directive 2012/19/EU of the European Parliament on waste electrical and electronic equipment (WEEE), and pursuant to and in accordance with Article 20 of the Directive 2013/56/EU of the European Parliament on batteries and accumulators and waste batteries. **+{{:wiki:manual_mcf-lw12co2e:1200px-weee_symbol_vectors.svg.png?nolink&50 |}}**Pursuant to and in accordance with Article 14 of the Directive 2012/19/EU of the European Parliament on waste electrical and electronic equipment (WEEE), and pursuant to and in accordance with Article 20 of the Directive 2013/56/EU of the European Parliament on batteries and accumulators and waste batteries. **
  
 The barred symbol of the rubbish bin shown on the equipment indicates that, at the end of its useful life, the product must be collected separately from other waste.  The barred symbol of the rubbish bin shown on the equipment indicates that, at the end of its useful life, the product must be collected separately from other waste. 
Line 150: Line 150:
 {{ :wiki:manual_mcf-lw12terwp:batt_res.jpg?400 |}} {{ :wiki:manual_mcf-lw12terwp:batt_res.jpg?400 |}}
  
-To perform the operation, you need a unique reset code that must be requested to enginko (please provide the DevEUI of the sensor when you ask for that code):+To perform the operation, you need a unique reset code that must be requested to Angel4Future (please provide the DevEUI of the sensor when you ask for that code):
      
 {{ :wiki:manual_mcf-lw12co2e:battery_res_0.jpg?400 |}} {{ :wiki:manual_mcf-lw12co2e:battery_res_0.jpg?400 |}}
Line 158: Line 158:
 ==== 2.6 Firmware update====  ==== 2.6 Firmware update====
  
-Save the firmware file (.FW) on the smartphone, and upload it with LoraTool App:+Download the latest firmwares available on the smartphone with LoRaTool app: 
 + 
 +{{ :wiki:manual_egk-lw20w00:update_firmwares.jpg?direct&400 |}} 
 + 
 +{{ :wiki:manual_egk-lw22plg:fwdownload.jpg?nolink&400 |}} 
 + 
 +{{ :wiki:manual_egk-lw22plg:fwdownload1.jpg?nolink&400 |}} 
 + 
 +Update the sensor with LoRaTool:
  
 {{ :wiki:manual_mcf-LW12CO2E:fw_0.jpg?400 |}} {{ :wiki:manual_mcf-LW12CO2E:fw_0.jpg?400 |}}
Line 170: Line 178:
 ==== 3.1 Period ==== ==== 3.1 Period ====
  
-Period is the interval (in minutes) between one measure and the next one. The sensor sends one measures for every transmission. +Period is the interval (in minutes) between one measure and the next one. The sensor sends three measures for every transmission. 
-Value can be between 15 and 65535 minutes (default: 30 minutes).+Value can be between 10 and 65535 minutes (default: 10 minutes).
  
 Period interval can be set with App or with downlink command.  Period interval can be set with App or with downlink command. 
Line 213: Line 221:
 {{ :wiki:manual_mcf-lw12co2e:activation1_0.jpg?400 |}} {{ :wiki:manual_mcf-lw12co2e:activation1_0.jpg?400 |}}
  
-The device exits factory activated with **NONE** mode.+The device exits factory activated with **OTAA ENGINKO** mode.
 On request devices can be shipped aleady activated. On request devices can be shipped aleady activated.
  
 Note: in **OTAA** AppKey is write only, in reading the field will always be empty, even if set. Note: in **OTAA** AppKey is write only, in reading the field will always be empty, even if set.
- 
------ 
- === Time sync == 
- 
-{{:warning.png?50|}} 
- 
-Normally sensor asks for a time sync at every power on (uplink starting with 01) or once a week. 
-If no or wrong reply received it will retry after 1 hour. 
-  
-  
-If not handled in the right way can cause a unnecessary battery consumption (battery life < 2 years). 
- 
-Please check chapter 2.1 of "DATA FRAME FORMAT" document. 
-  
-  
- 
-  
- 
- 
- 
  
 ==== 4.2 Other settings ==== ==== 4.2 Other settings ====
Line 264: Line 252:
 If not handled in the right way can cause a unnecessary battery consumption (battery life < 2 years). If not handled in the right way can cause a unnecessary battery consumption (battery life < 2 years).
  
-Please check chapter 2.1 of "DATA FRAME FORMAT" document.+Please check chapter 2.1 [[data_frame_format| DATA FRAME FORMAT]]
 ----- -----
  
Line 301: Line 289:
  
  
-To bring back the sensor to factory default and reset the passwords, a reset code must be requested to enginko (please provide the DevEUI of the sensor when you ask for that code).+To bring back the sensor to factory default and reset the passwords, a reset code must be requested to Angel4Future (please provide the DevEUI of the sensor when you ask for that code).
  
 ===== 6 Configuration file =====  ===== 6 Configuration file =====
  
-WIth LoRa Tool App is possible to configure the device using an XML file, instead to manually adjust the parameters (for details about the file format please ask to enginko). This is very useful especially in +WIth LoRa Tool App is possible to configure the device using an XML file, instead to manually adjust the parameters (for details about the file format please ask to Angel4Future). This is very useful especially in 
 case of multiple devices configuration. case of multiple devices configuration.
  
-With "Save" button an XML file with the actual configuration of the sensor will be generated. This is useful to store or clone the configuration, or to send it to enginko's support if needed.+With "Save" button an XML file with the actual configuration of the sensor will be generated. This is useful to store or clone the configuration, or to send it to Angel4Future's support if needed.
  
  
Line 326: Line 314:
 When the sensor is approached, if one parameter is different from files, the APP will ask you if you want to overwrite. When the sensor is approached, if one parameter is different from files, the APP will ask you if you want to overwrite.
    
-XLS is prevailing on the XML, so if both files are enabled, if the DevEUI of the device matches one of the DevEUIS is in the XLS file, LoRa parameters will be setted from this one.+XLS is prevailing on the XML, so if both files are enabled, if the DevEUI of the device matches one of the DevEUIs in the XLS file, LoRa parameters will be setted from this one..
  
 These configuration can be done in the in the Settings: These configuration can be done in the in the Settings:
Line 339: Line 327:
  
  
-For details on files format please ask to enginko.+For details on files format please ask to Angel4Future.
 ===== 7 LoRaWEB Tool ===== ===== 7 LoRaWEB Tool =====
  
-enginko provides, upon free registration, **LoRaWEB** online tool,  where for each sensor it is possible to find documentation, javascript examples for parsing, downlink generator and uplink decoder:+Angel4Future provides free **LoRaWEB** online tool,  where for each sensor it is possible to find documentation, javascript examples for parsing, downlink generator and uplink decoder:
  
 [[https://iot.mcf88.cloud/LoRaWeb/#/configuration|LoRaWEB Tool]] [[https://iot.mcf88.cloud/LoRaWeb/#/configuration|LoRaWEB Tool]]
Line 369: Line 357:
 ===== 10 Declaration of conformity ===== ===== 10 Declaration of conformity =====
  
-Hereby, enginko Srl declares that MCF-LW12TERWP complies with the essential requirements and other relevant provisions of Directive  2014/53/EU. +Declarations of conformity are available from Angel4Future by sending a request email to sensor@enginko.com.
  
 ===== 11 Contacts ===== ===== 11 Contacts =====
Last modified: 2023/05/29 07:33